Configuration Assistant 3.2 3 English Installer

#Configuration Assistant 3.2 3 English Installer install
#Configuration Assistant 3.2 3 English Installer archive
#Configuration Assistant 3.2 3 English Installer registration
#Configuration Assistant 3.2 3 English Installer software
#Configuration Assistant 3.2 3 English Installer password

Note By default, the HTTP and secure server are enabled for factory fresh routers.

Non-Secure mode-Uses HTTP and requires HTTP Server to be enabled on the router.

Secure mode-Uses HTTPS and requires HTTP Secure Server to be enabled on the router.

(Optional) Primary and secondary DNS IP addressesД¬isco CP Express can be accessed in one of these two modes:.

#Configuration Assistant 3.2 3 English Installer password

Username and password to access the Password Authentication Protocol (PAP) or Challenge Handshake Authentication Protocol (CHAP) if you use ADSL as a WAN.Virtual Channel Identifier (VCI) and Virtual Path Identifier (VPI) values if you use Asymmetric Digital Subscriber Line (ADSL) as a Wide Area Network (WAN).Step 10 Press Return to confirm the deletion.Д«efore you launch the Cisco CP Express Admin View, gather the following information from your service provider: Step 9 After the installation is complete, delete the ccpexpressAdmin_3_2_en.tar file from the flash memory of the router, as shown in this example: router# delete flash:ccpexpressAdmin_3_2_en.tar Specify the name of the destination file, as shown in this example: Destination file name ? ccpExpress_ap_express-security_en.shtml.gz Specify the name of the source file that is to be copied onto the routerвЂ™s flash memory, as shown in this example: Source filename ? ccpExpress_ap_express-security_en.shtml.gz Specify the IP address of the FTP or TFTP server, as shown in this example: Address or name of remote host ? ДЇ. Note Ensure that you copy the ccpExpress_ap_express-security_en.shtml.gz file to that folder with a name beginning with the prefix вЂњap-801-вЂќ or вЂњap802-вЂќ, and ensure that this folder contains the html/level/15/ sub-directories under it.Д®. Copy the ccpExpress_ap_express-security_en.shtml.gz file to the wireless flash, as shown in this example: ap# copy tftp: flash If the ccpExpress_ap_express-security_en.shtml.gz file is not available on the wireless flash memory, proceed to step d. Note By default, the ccpExpress_ap_express-security_en.shtml.gz file is available on some versions of the IOS AP.Д¬. Verify that the ccpExpress_ap_express-security_en.shtml.gz file already exists on the вЂњap-801-вЂќ or вЂњap802-вЂќ folder of the wireless flash memory, as shown in this example: ap# cd /html/level/15/ ap# dir Telnet to the WAP of the router, as shown in this example: ap#> enable Password: passwordД«. Step 8 If the router supports a wireless configuration, configure it, thus:ДЄ.

#Configuration Assistant 3.2 3 English Installer archive

Step 7 Extract the ccpexpressAdmin31.tar file onto the routerвЂ™s flash memory, as shown in this example: router# archive tar /xtract flash:ccpexpressAdmin_3_2_en.tar flash:/

Step 6 Specify the name of the destination file, as shown in this example: Destination file name ? ccpexpressAdmin_3_2_en.tar Step 5 Specify the name of the source file that is to be copied onto the routerвЂ™s flash memory, as shown in this example: Source filename ? ccpexpressAdmin_3_2_en.tar Where is the IP address of the FTP or TFTP server. Step 4 Specify the IP address of the FTP or TFTP server, as shown in this example: Address or name of remote host ? router> enable Password: password router# copy tftp: flash Step 3 Using an FTP or TFTP server, copy the extracted files onto the routerвЂ™s flash memory.

The cisco-config-pro-exp-admin-k9-3_2-en.zip file contains these files: ccpexpressAdmin3_2_en.tar and ccpExpress_ap_express-security_en.shtml.gz. Step 2 Extract the compressed file, cisco-config-pro-exp-admin-k9-3_2-en.zip file into the system. Note For Japanese version, download cisco-config-pro-exp-admin-k9-3_2-ja.zip then follow the remaining instructions. Step 1 Download the compressed file, cisco-config-pro-exp-admin-k9-3_2-en.zip from the following web link:

#Configuration Assistant 3.2 3 English Installer install

To install the Cisco CP Express Admin View on the routerвЂ™s flash memory, perform these steps: This compressed file contains the Cisco CP Express Admin View installation files. Step 4 Select the Cisco Configuration Professional Express 3.2 package link and click Download to download the compressed file, cisco-config-pro-exp-admin-k9-3_2-en.zip to the sy stem.

#Configuration Assistant 3.2 3 English Installer software

Step 3 From the Download Software page, choose the release to download.

#Configuration Assistant 3.2 3 English Installer registration

Click Regi ster (at the top of the page) to complete the registration process, and then return to this page. If you do not have login credentials, regi ster and obtain login credentials. Step 2 When a login page appears, enter your login credentials and click Log In. Step 1 Launch the browser, and go to the following web link:

To download Cisco CP Express Admin View, perform these steps: Downloading Cisco CP Express Admin View.Installing and Setting Up Cisco CP Express Admin View